Service tools

4 -	Service tools

Spare parts catalogue


MTS 1200 ABS	Workshop service tools
MTS 1200 ABS	Workshop service tools
MTS 1200 S ABS	Workshop service tools
MTS 1200 S ABS	Workshop service tools

Specific tools for the engine


Code no.	Description
88713.2011	Tool to lock crankshaft at Top Dead Centre
88713.2676	Wrench for tightening cylinder head nuts
88713.2103	Stand for cylinder head assembly
88713.0123	Timing check tool
88713.1821	Wrench for tightening timing belt tensioner pulley shafts
88713.2861	Camshaft oil seal installer
88713.2060	Gearbox output shaft oil seal installer
88713.1806	Holding tool for pulley tightening
97900.0215	DDS (Ducati Diagnosis System) + cylinder vacuum meter kit
88765.1518	Valve lift gauge
88713.2878	Fork-type feeler gauge 0.2 mm, 0.3 mm
88713.3367	Flywheel tool
88713.1920	Tool for installing O-rings on crankcase studs
88713.3334	Plate for gear selector fork positioning
88713.2442	Tool for installation of sealing ring on valve-guide
88713.1749	Puller for drive pulley and cover
88713.1832	Engine repair bench
88713.3408	Wet FCC clutch drum holding tool
88765.1623	Distribution pulley timing tool
88713.1886	Engine cover sheet
88713.1010	Exhaust gases pick-up connector
88713.1805	Tool for tightening timing belt driveshaft pulley
88765.1188	Top Dead Centre test gauge
88713.3219	Holding tool for pulley tightening
88713.0869	Water pump front seal installer
88713.0870	Installation tool for counter plate for water pump front seal
88700.5749	Crankcase assembly cap
88713.2877	Sparkplug wrench
88713.1980	Punch for installing caps on shafts
88713.3497	Timing belt tensioner pulley wrench
88765.1298	Spacer lower register control valve
88713.2870	Connecting rod guide tool
88713.2834	Punch to install circlip on the camshaft
88713.3406	Wrench for tightening primary sprocket nut
88713.2906	Oil filter cartridge wrench
88713.3417	Torque wrench for tightening front sprocket nut
88713.3407	Bush (gear position sensor)
88713.3352	Timing tool (clutch plates series)
88713.2069	Rocker arm springs tensioning kit

Spare parts catalogue


MTS 1200 ABS	Workshop service tools
MTS 1200 S ABS	Workshop service tools

Specific tools for the frame


Code no.	Description
88713.1072	Drift to install half bearing in bottom yoke
88713.2562	Chain assembly tool
88713.1058	Wrench for steering shaft nut
88713.1062	Tool for installing steering head bearings
88713.1071	Drift for installing the rocker arm needle roller bearings
88713.2951	Rear wheel balancing tool
88713.3211	Wrench for adjustment of the eccentric hub
88713.3204	MARZOCCHI fork service tool - Sealing ring fitting
88713.3203	Pull bar for MARZOCCHI fork service
88713.1074	Swingarm pivot bolt removal tool
88713.3501	Fuel sensor tightening wrench
88713.1068	Drift for installing the swingarm needle roller bearings
88713.2409	Swingarm ball bearing installation tool
88713.3526	Frame plates assembling wrench
88713.3527	Tool for removing the sliding bushes (Öhlins)
88713.3528	Tool for assembling the sliding bushes (Öhlins)
88713.3529	Bushes supporting bracket (Öhlins)
88713.3465	Bush to install/remove the Öhlins fork plug
88713.3396	Engine repair bench
8000.70139	Front wheel shaft wrench

Spare parts catalogue


MTS 1200 ABS	DDS tester
MTS 1200 ABS	Workshop service tools
MTS 1200 S ABS	DDS tester
MTS 1200 S ABS	Workshop service tools

Appropriate diagnosis tools


Code no.	Description
97900.0211	DDS (Ducati Diagnosis System) without cables
97900.0227	Power cable and diagnosis
97900.0222	Power cable and diagnosis 1060838 (Measurement Module)
97900.0218	Vacuum sensor
552.1.039.1A	Pressure sensor
97900.0220	Pressure/vacuum tube
97900.0221	Union
97900.0228	Battery socket adapter
814.1.114.1A	Oil pressure coupling
514.1.032.1A	Auxiliary test cable
552.1.038.1A	Cylinder compression cable M10 fitting
875.1.065.1A	Oil pressure tube
97900.0230	Feeder
97900.0224	Feeder
88765.1371	Belt tensioning sensor
88765.1374	Belt tensioning sensor bracket
590.1.189.1A	Fuel pressure tube
88765.1126	Clamp-type amperemeter
97900.0227S	CAN network diagnosis cable